HVAC Estimating Estimating in Irving, TX

Equipment sized and priced off a real load calculation - not a tonnage-per-square-foot rule of thumb that guesses at what a Texas summer actually does to a building.

An HVAC estimate is only as good as the load calculation underneath it, and load is the input most templated estimates skip. A national average that prices "2 tons per 800 square feet" ignores the fact that Texas sits in the DOE's South Region, which carries a higher minimum efficiency standard than most of the country - 14.3 SEER2 for most residential split systems under 45,000 BTU, against 13.4 in the DOE's North Region - and it ignores that a west-facing glass wall in Dallas or a slab-on-grade home in Houston humidity carries a real, calculable load that a flat square-footage ratio simply doesn't capture. Get the load wrong and everything downstream - equipment tonnage, duct sizing, and the resulting cost - is wrong with it.

Our HVAC estimating starts with the load calculation, not the equipment catalog, so the tonnage and duct design that gets priced actually matches what the building needs.

• Load calculation - residential loads run per ACCA Manual J (heating and cooling load) and equipment matched per Manual S; commercial loads run per ASHRAE methodology, driven by occupancy, glazing, and ventilation requirements.
• Equipment selection and pricing - condensers, air handlers, furnaces, and heat pumps priced to DOE South Region efficiency minimums, which apply statewide in Texas regardless of where in the country a national price sheet was built.
• Ductwork takeoff - supply, return, and exhaust ductwork sized per Manual D (residential) or engineered duct design (commercial), quantified by material, gauge, and insulation type.
• Refrigerant piping - line set sizing and refrigerant type priced to the specified equipment, accounting for ongoing federal refrigerant phase-down rules that affect both equipment cost and availability.
• Controls and thermostats - from basic residential thermostats to commercial BMS integration points, priced as their own line item rather than bundled into equipment cost.
• Ventilation - outdoor air, exhaust, and makeup air systems sized to occupancy and code minimums, priced separately from general supply/return ductwork.

Residential. Central air and heat pump systems sized per Manual J/S/D, priced to actual house load and DOE South Region equipment minimums - not a flat tonnage-per-square-foot guess.

Light commercial. Rooftop package units and split systems sized to ASHRAE-calculated occupancy load, common on retail, office, and small medical buildouts.

New construction vs. replacement. New-construction estimates size equipment to the building's full calculated load; replacement/retrofit estimates account for existing duct condition and any load changes since original installation (added glazing, insulation upgrades, or occupancy changes).

Undersized equipment runs constantly through a Texas summer and never quite catches up on the hottest days; oversized equipment short-cycles, wastes installation dollars on capacity the building doesn't need, and struggles with humidity control because it satisfies the thermostat before it's run long enough to properly dehumidify the space. Both mistakes trace back to the same root cause - pricing equipment off a guessed tonnage instead of a real Manual J or ASHRAE calculation. Running the load calculation first, before selecting equipment, is what keeps a Texas HVAC estimate from repeating that mistake.

Load calculations are run to ACCA Manual J/S/D (residential) and ASHRAE methodology (commercial). Ductwork and equipment takeoffs are built in Bluebeam and FastDUCT/FastPIPE, with equipment priced against current DOE efficiency standards and cross-checked against RSMeans and current Texas labor rates.

Load calculations and equipment pricing require specific technical knowledge - Manual J/S/D methodology, DOE regional standards, and current refrigerant rules aren't something a general estimator picks up casually. Our estimators run the calculation correctly the first time, so the tonnage you bid is the tonnage the building actually needs.

Irving's construction market is dominated by two massive economic engines: the master-planned corporate epicenter of Las Colinas, and the logistics/industrial boom surrounding DFW International Airport. It is one of the most dynamic commercial markets in North Texas.

Estimating in Irving often means pricing high-end corporate headquarters, complex mixed-use developments along Lake Carolyn, or massive tilt-wall cargo and distribution facilities adjacent to the airport.

Building in Irving, and specifically in Las Colinas, involves strict oversight. The Las Colinas Association (LCA) enforces rigorous architectural controls, landscaping standards, and material requirements that go beyond standard city code. Our estimates capture these premium costs, ensuring your bid accounts for the mandatory high-end finishes and site improvements.